[Hackrf-dev] DFU

[Graham Cottew]

Yes I can do that as well but it doesn't "stick" and as soon as I power off it's back to ground zero.
I have to go through DFU again to get the board up able to be recognised by hackrf_info.

I have also been running 'make program' from the hackrf_usb directory with the same results.
Once after about 50 DFU's it programmed successfully and I started to write a email to this group to announce I had it licked. 
I used it on another machine and it was powering on and off and booting fine but then after I did a hackrf_spiflash to update to the 2013.07.01 firmware it nuked it back to the present state again and I had to accept defeat.

On 08/08/2013, at 3:47 AM, Russell Hande <zefie at persona.cc> wrote:


> I think once it is booted in DFU mode, you should be able to re-flash

> the rom_to_ram firmware.

> 

> On Wed, Aug 7, 2013 at 3:26 AM, Graham Cottew <gc at zendata.com> wrote:

>> With the hackrf_usb.dfu file you sent me and dfu-utils v 0.7 I can do a DFU that appears OK

>> 

>> The Jawbreaker is then found by hackrf_info and works fine with gnuradio on Tx and Rx

>> VCCLED, 1V8LED and LED1 are all on when it is idle

>> 

>> Problem is when I power cycle the board the DFU firmware just disappears and I am left with

>> VCCLED on

>> 1V8LED off

>> LED1, LED2, LED3, USB_LED0, USB_LED1 all dimly lit

>> 

>> Can you suggest what I can do to overcome needing to DFU every time I use the Jawbreaker?

>> 

>> DFU:

>> 

>> $ sudo dfu-util --device 1fc9:000c --alt 0 --download hackrf_usb.dfu

>> Password:

>> dfu-util 0.7

>> 

>> Copyright 2005-2008 Weston Schmidt, Harald Welte and OpenMoko Inc.

>> Copyright 2010-2012 Tormod Volden and Stefan Schmidt

>> This program is Free Software and has ABSOLUTELY NO WARRANTY

>> Please report bugs to dfu-util at lists.gnumonks.org

>> 

>> Filter on vendor = 0x1fc9 product = 0x000c

>> Opening DFU capable USB device... ID 1fc9:000c

>> Run-time device DFU version 0100

>> Claiming USB DFU Runtime Interface...

>> Determining device status: state = dfuIDLE, status = 0

>> WARNING: Runtime device already in DFU state ?!?

>> Found Runtime: [1fc9:000c] devnum=0, cfg=1, intf=0, alt=0, name="DFU"

>> Claiming USB DFU Interface...

>> Setting Alternate Setting #0 ...

>> Determining device status: state = dfuIDLE, status = 0

>> dfuIDLE, continuing

>> DFU mode device DFU version 0100

>> Device returned transfer size 2048

>> DFU CRC does not match

>> Warning: File has no DFU suffix

>> bytes_per_hash=346

>> Copying data from PC to DFU device

>> Starting download: [##################################################] finished!

>> unable to read DFU status

>> 

>> HackRF_Info:

>> 

>> $ hackrf_info

>> Found HackRF board.

>> Board ID Number: 1 (Jawbreaker)

>> Firmware Version: git-b056efc

>> Part ID Number: 0xbc654755 0xbc654755

>> Serial Number: 0x00000000 0x00000000 0x505062c8 0x367b9917

>> _______________________________________________

>> HackRF-dev mailing list

>> HackRF-dev at greatscottgadgets.com

>> http://nine.pairlist.net/mailman/listinfo/hackrf-dev