[Hackrf-dev] Testing a new HackRF One

[Michael Ossmann]

You need the very latest sdr# from sdrsharp.com.  It is particularly
important that your hackrf.dll is up to date.


On Wed, Aug 13, 2014 at 07:10:48AM -0700, Dan Koellen wrote:
>
> Thanks scateu
> 
> I should have been more clear, I could not get SDR# to connect with the
> HackRF board.  I received the 'USB driver not installed or board is not
> connected' error message even though I loaded WinUSB with zadig
> 
> I'll keep in mind your configuration suggestions when I get SDR# to see my
> board.
> 
> When running Pentoo the HackRF board was found with hackrf_info command
> 
> Thanks, phase2682
> 
> -----Original Message-----
> From: scateu [mailto:scateu at gmail.com]
> Sent: Wednesday, August 13, 2014 7:04 AM
> To: Dan Koellen
> Cc: mr2dave; Jon B; hackrf-dev at greatscottgadgets.com
> Subject: Re: [Hackrf-dev] Testing a new HackRF One
> 
> Hi,
> 
> You may need to click the configuration icon ( gear ) , and check “Amp”
> on, then set LNA(Low Noise Amplifier) gain and VGA(Variable Gain Amplifier)
> to about 1/3 to the right.
> 
> Oh, you need to click the ‘play’ button first, or those slider and
> checkbox would be grey.
> 
> 
> Cheers,
> scateu
> 
> 在 2014年8月13日，下午9:36，Dan Koellen <phase2682 at gmail.com> 写道：
> 
> > I had problems getting SDR# running with HackRF also.  I had been using
> SDR#
> > with a RTL dongle for a while with no problems.
> >
> > Is there a newer version of SDR# I should install that will work with
> > HackRF?
> >
> > I just imaged Pentoo and have to learn GNU radio now.   I was hoping to
> > bring HackRF up faster with SDR# that I am already familiar with.
> >
> > -----Original Message-----
> > From: HackRF-dev [mailto:hackrf-dev-bounces at greatscottgadgets.com] On
> Behalf
> > Of mr2dave
> > Sent: Tuesday, August 12, 2014 11:26 PM
> > To: Jon B
> > Cc: hackrf-dev at greatscottgadgets.com
> > Subject: Re: [Hackrf-dev] Testing a new HackRF One
> >
> > Try running zadig with hackrf plugged in.
> > From the Options menu, select List All Devices.
> > Select HackRF One from the drop-down menu.
> > Verify that the WinUSB driver is loaded on the left. If it isn't,
> > install it again now.
> > If all else fails, load up Pentoo.
> >
> >
> > On Tue, 2014-08-12 at 20:59 -0600, Jon B wrote:
> >> I'm looking for a quick (Windows based way) to make sure the hardware
> >> works.
> >>
> >>
> >> I'm not sure my new HackRF One works.
> >>
> >>
> >> Anybody have any hints on how to configure SDR#?
> >>
> >>
> >> Here is what I've done:
> >>
> >>
> >> I attached the antenna to the antenna port.
> >>
> >> I downloaded SDR#.
> >> I installed SDR#.
> >> I installed the driver by running zadig (the one from the sdrsharp
> >> directory).
> >> Plugged in the HackRF One.
> >> Ran SDRSharp.
> >> Configured source = HackRF, Radio = NFM.  Then hit start.
> >> Set the frequency to 89MHz.
> >>
> >>
> >> I see a flat spectra spanning 86 to 96 MHz at -77.  As I roll around
> >> the spectrum I get nothing.
> >>
> >>
> >> The HackRF leds are all lit except TX.
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >>
> >> _______________________________________________
> >> HackRF-dev mailing list
> >> HackRF-dev at greatscottgadgets.com
> >> http://nine.pairlist.net/mailman/listinfo/hackrf-dev
> >
> >
> > _______________________________________________
> > HackRF-dev mailing list
> > HackRF-dev at greatscottgadgets.com
> > http://nine.pairlist.net/mailman/listinfo/hackrf-dev
> >
> > _______________________________________________
> > HackRF-dev mailing list
> > HackRF-dev at greatscottgadgets.com
> > http://nine.pairlist.net/mailman/listinfo/hackrf-dev
> 
> _______________________________________________
> HackRF-dev mailing list
> HackRF-dev at greatscottgadgets.com
> http://nine.pairlist.net/mailman/listinfo/hackrf-dev