[Hackrf-dev] Testing a new HackRF One

[Paul Connolly]

A lot of people appear to be using this out of date guide that tells
them incorrectly to overwrite the hackrf.dll with one from November last
year.
http://superfro.org/setting-up-hackrf-in-windows-with-sdr/

On 13/08/2014 16:47, Michael Ossmann wrote:
> You need the very latest sdr# from sdrsharp.com.  It is particularly
> important that your hackrf.dll is up to date.
>
>
> On Wed, Aug 13, 2014 at 07:10:48AM -0700, Dan Koellen wrote:
>> Thanks scateu
>>
>> I should have been more clear, I could not get SDR# to connect with the
>> HackRF board.  I received the 'USB driver not installed or board is not
>> connected' error message even though I loaded WinUSB with zadig
>>
>> I'll keep in mind your configuration suggestions when I get SDR# to see my
>> board.
>>
>> When running Pentoo the HackRF board was found with hackrf_info command
>>
>> Thanks, phase2682
>>
>> -----Original Message-----
>> From: scateu [mailto:scateu at gmail.com]
>> Sent: Wednesday, August 13, 2014 7:04 AM
>> To: Dan Koellen
>> Cc: mr2dave; Jon B; hackrf-dev at greatscottgadgets.com
>> Subject: Re: [Hackrf-dev] Testing a new HackRF One
>>
>> Hi,
>>
>> You may need to click the configuration icon ( gear ) , and check “Amp”
>> on, then set LNA(Low Noise Amplifier) gain and VGA(Variable Gain Amplifier)
>> to about 1/3 to the right.
>>
>> Oh, you need to click the ‘play’ button first, or those slider and
>> checkbox would be grey.
>>
>>
>> Cheers,
>> scateu
>>
>> 在 2014年8月13日，下午9:36，Dan Koellen <phase2682 at gmail.com> 写道：
>>
>>> I had problems getting SDR# running with HackRF also.  I had been using
>> SDR#
>>> with a RTL dongle for a while with no problems.
>>>
>>> Is there a newer version of SDR# I should install that will work with
>>> HackRF?
>>>
>>> I just imaged Pentoo and have to learn GNU radio now.   I was hoping to
>>> bring HackRF up faster with SDR# that I am already familiar with.
>>>
>>> -----Original Message-----
>>> From: HackRF-dev [mailto:hackrf-dev-bounces at greatscottgadgets.com] On
>> Behalf
>>> Of mr2dave
>>> Sent: Tuesday, August 12, 2014 11:26 PM
>>> To: Jon B
>>> Cc: hackrf-dev at greatscottgadgets.com
>>> Subject: Re: [Hackrf-dev] Testing a new HackRF One
>>>
>>> Try running zadig with hackrf plugged in.
>>> From the Options menu, select List All Devices.
>>> Select HackRF One from the drop-down menu.
>>> Verify that the WinUSB driver is loaded on the left. If it isn't,
>>> install it again now.
>>> If all else fails, load up Pentoo.
>>>
>>>
>>> On Tue, 2014-08-12 at 20:59 -0600, Jon B wrote:
>>>> I'm looking for a quick (Windows based way) to make sure the hardware
>>>> works.
>>>>
>>>>
>>>> I'm not sure my new HackRF One works.
>>>>
>>>>
>>>> Anybody have any hints on how to configure SDR#?
>>>>
>>>>
>>>> Here is what I've done:
>>>>
>>>>
>>>> I attached the antenna to the antenna port.
>>>>
>>>> I downloaded SDR#.
>>>> I installed SDR#.
>>>> I installed the driver by running zadig (the one from the sdrsharp
>>>> directory).
>>>> Plugged in the HackRF One.
>>>> Ran SDRSharp.
>>>> Configured source = HackRF, Radio = NFM.  Then hit start.
>>>> Set the frequency to 89MHz.
>>>>
>>>>
>>>> I see a flat spectra spanning 86 to 96 MHz at -77.  As I roll around
>>>> the spectrum I get nothing.
>>>>
>>>>
>>>> The HackRF leds are all lit except TX.
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> HackRF-dev mailing list
>>>> HackRF-dev at greatscottgadgets.com
>>>> http://nine.pairlist.net/mailman/listinfo/hackrf-dev
>>>
>>> _______________________________________________
>>> HackRF-dev mailing list
>>> HackRF-dev at greatscottgadgets.com
>>> http://nine.pairlist.net/mailman/listinfo/hackrf-dev
>>>
>>> _______________________________________________
>>> HackRF-dev mailing list
>>> HackRF-dev at greatscottgadgets.com
>>> http://nine.pairlist.net/mailman/listinfo/hackrf-dev
>> _______________________________________________
>> HackRF-dev mailing list
>> HackRF-dev at greatscottgadgets.com
>> http://nine.pairlist.net/mailman/listinfo/hackrf-dev
> _______________________________________________
> HackRF-dev mailing list
> HackRF-dev at greatscottgadgets.com
> http://nine.pairlist.net/mailman/listinfo/hackrf-dev

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://nine.pairlist.net/pipermail/hackrf-dev/attachments/20140813/6d732daf/attachment-0001.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 834 bytes
Desc: OpenPGP digital signature
URL: <http://nine.pairlist.net/pipermail/hackrf-dev/attachments/20140813/6d732daf/attachment-0001.pgp>