[Hackrf-dev] Testing a new HackRF One

[Dennis Liang]

I hope this get fixed…wanted to start playing with hackrf more…I had the same problem with the prototype. Is there a good firmware customization guide. Maybe we can change the PNP id so they match for us windows haxor. 

 

I do expect to see some sort of guide/tutorial in the linux GNU radio side too…

 

-D

 

From: HackRF-dev [mailto:hackrf-dev-bounces at greatscottgadgets.com] On Behalf Of Paul Connolly
Sent: Wednesday, August 13, 2014 10:09 AM
To: hackrf-dev at greatscottgadgets.com
Subject: Re: [Hackrf-dev] Testing a new HackRF One

 

A lot of people appear to be using this out of date guide that tells them incorrectly to overwrite the hackrf.dll with one from November last year.
http://superfro.org/setting-up-hackrf-in-windows-with-sdr/

On 13/08/2014 16:47, Michael Ossmann wrote:

	You need the very latest sdr# from sdrsharp.com.  It is particularly
	important that your hackrf.dll is up to date.
	 
	 
	On Wed, Aug 13, 2014 at 07:10:48AM -0700, Dan Koellen wrote:

		 
		Thanks scateu
		 
		I should have been more clear, I could not get SDR# to connect with the
		HackRF board.  I received the 'USB driver not installed or board is not
		connected' error message even though I loaded WinUSB with zadig
		 
		I'll keep in mind your configuration suggestions when I get SDR# to see my
		board.
		 
		When running Pentoo the HackRF board was found with hackrf_info command
		 
		Thanks, phase2682
		 
		-----Original Message-----
		From: scateu [mailto:scateu at gmail.com]
		Sent: Wednesday, August 13, 2014 7:04 AM
		To: Dan Koellen
		Cc: mr2dave; Jon B; hackrf-dev at greatscottgadgets.com
		Subject: Re: [Hackrf-dev] Testing a new HackRF One
		 
		Hi,
		 
		You may need to click the configuration icon ( gear ) , and check “Amp”
		on, then set LNA(Low Noise Amplifier) gain and VGA(Variable Gain Amplifier)
		to about 1/3 to the right.
		 
		Oh, you need to click the ‘play’ button first, or those slider and
		checkbox would be grey.
		 
		 
		Cheers,
		scateu
		 
		在 2014年8月13日，下午9:36，Dan Koellen <phase2682 at gmail.com> <mailto:phase2682 at gmail.com>  写道：
		 

			I had problems getting SDR# running with HackRF also.  I had been using

		SDR#

			with a RTL dongle for a while with no problems.
			 
			Is there a newer version of SDR# I should install that will work with
			HackRF?
			 
			I just imaged Pentoo and have to learn GNU radio now.   I was hoping to
			bring HackRF up faster with SDR# that I am already familiar with.
			 
			-----Original Message-----
			From: HackRF-dev [mailto:hackrf-dev-bounces at greatscottgadgets.com] On

		Behalf

			Of mr2dave
			Sent: Tuesday, August 12, 2014 11:26 PM
			To: Jon B
			Cc: hackrf-dev at greatscottgadgets.com
			Subject: Re: [Hackrf-dev] Testing a new HackRF One
			 
			Try running zadig with hackrf plugged in.
			From the Options menu, select List All Devices.
			Select HackRF One from the drop-down menu.
			Verify that the WinUSB driver is loaded on the left. If it isn't,
			install it again now.
			If all else fails, load up Pentoo.
			 
			 
			On Tue, 2014-08-12 at 20:59 -0600, Jon B wrote:

				I'm looking for a quick (Windows based way) to make sure the hardware
				works.
				 
				 
				I'm not sure my new HackRF One works.
				 
				 
				Anybody have any hints on how to configure SDR#?
				 
				 
				Here is what I've done:
				 
				 
				I attached the antenna to the antenna port.
				 
				I downloaded SDR#.
				I installed SDR#.
				I installed the driver by running zadig (the one from the sdrsharp
				directory).
				Plugged in the HackRF One.
				Ran SDRSharp.
				Configured source = HackRF, Radio = NFM.  Then hit start.
				Set the frequency to 89MHz.
				 
				 
				I see a flat spectra spanning 86 to 96 MHz at -77.  As I roll around
				the spectrum I get nothing.
				 
				 
				The HackRF leds are all lit except TX.
				 
				 
				 
				 
				 
				 
				 
				 
				_______________________________________________
				HackRF-dev mailing list
				HackRF-dev at greatscottgadgets.com
				http://nine.pairlist.net/mailman/listinfo/hackrf-dev

			 
			 
			_______________________________________________
			HackRF-dev mailing list
			HackRF-dev at greatscottgadgets.com
			http://nine.pairlist.net/mailman/listinfo/hackrf-dev
			 
			_______________________________________________
			HackRF-dev mailing list
			HackRF-dev at greatscottgadgets.com
			http://nine.pairlist.net/mailman/listinfo/hackrf-dev

		 
		_______________________________________________
		HackRF-dev mailing list
		HackRF-dev at greatscottgadgets.com
		http://nine.pairlist.net/mailman/listinfo/hackrf-dev

	_______________________________________________
	HackRF-dev mailing list
	HackRF-dev at greatscottgadgets.com
	http://nine.pairlist.net/mailman/listinfo/hackrf-dev

 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://nine.pairlist.net/pipermail/hackrf-dev/attachments/20140813/021db5a0/attachment-0001.html>